How to Draw an Equilateral Triangle

Опубликовал Admin
28-09-2016, 04:10
8 677
0
An equilateral triangle has three sides of equal length, connected by three angles of equal width. It can be challenging to draw a perfectly equilateral triangle by hand. However, you can use a circular object to mark out the angles. Make sure to use a ruler to get the lines straight! Continue reading to learn how to draw one.

Using a Compass

  1. Draw a straight line. Lay your ruler on the paper, then trace a pencil along the straight edge. This line segment will form one side of your equilateral triangle, which means that you will need to draw two more lines of exactly the same length, each reaching toward a point at a 60° angle from the first line. Make sure that you have plenty of room to draw all three sides!
  2. Span the segment with your compass. Slide a pencil into your compass, and make sure that it's sharp! Put the point of your compass at one end of the segment, and set the pencil point at the other.
  3. Trace a quarter-circle arc. Do not adjust the point of the compass, and do not change the set "width" of the tool from the compass point to the pencil point. Swing the pencil-point of the compass in a quarter-circle up and away from the line segment.
  4. Switch the compass around. Without changing the width of the compass spread, move the point of the compass to the other end.
  5. Draw a second arc. Carefully swing the pencil-point of the compass so that the new arc crosses over the first arc that you drew.
  6. Mark the point where the two arcs cross. This is the apex (the "top" point) of your triangle. It should lie at the exact center of the line segment that you've drawn. You can now draw two straight lines leading to this point: one from each end of the "bottom" line segment.
  7. Finish the triangle. Use a ruler to draw two more straight line segments: the remaining sides of the triangle. Connect each end of the original line segment to the point at which the arcs cross. Make sure that the lines are straight. To finish the job, erase the arcs that you drew so that only the triangle remains!
    • Consider tracing this triangle onto another page. This way, you can start fresh with a clean shape.
    • If you need a bigger or a smaller triangle, repeat the process but adjust the length of the original line segment. The longer the sides, the bigger the triangle!

Using an Object with a Circular Base

  1. Choose your circular object. Use almost any cylindrical object with a circular base, like a bottle or a soup can. Try using a circular roll of tape or a CD. If you are going to substitute the arc of this object for the arc of a compass tracer, you'll need to choose an object of the right size. In this method, each side of the equilateral triangle will be as long as the radius (half the diameter) of the circular object.
    • If you use a CD as your object: imagine an equilateral triangle that fits into the top-right quadrant of a CD.
  2. Draw the first side. It should be exactly as long as the radius of the circular object – the distance halfway across. Make sure that it is perfectly straight!
    • If you have a ruler: simply measure the diameter of the object and draw a line that is half as long.
    • If you don't have a ruler: place the circular object onto a sheet of paper, then carefully trace the circumference with your pencil. Remove the object, and you should have a perfect circle. Use a straight edge to draw a line across the exact center of the circle: the point that is completely equidistant from any point around the circumference of the circle.
  3. Use the circular object to trace an arc. Place the object over the line segment, with the edge of the circle resting at one end of the line. For accuracy, make sure that the line cleaves through the exact center of the circle. Use your pencil to trace an arc: roughly one-quarter of the way around the perimeter of the circle.
  4. Trace another arc. Now, shift the circular object so that the edge touches the other end of the line segment. Make sure that the line segment runs through the exact center of the circle. Draw another quarter-arc that crosses the first arc at a point directly above the line segment. This point is the apex of your triangle.
  5. Complete the triangle. Draw the remaining sides of the triangle: two more straight lines will connect the apex with the two open ends of the line segment. Now, you should have a perfectly equilateral triangle!

Using a Protractor

  1. Draw the first side. Use a ruler or the straight edge of your protractor to trace a straight line segment of an appropriate length. This line segment will become the first side of your triangle, and each of the other sides will be just as long – so make sure that it's the right size!
  2. Use a protractor to measure a 60° angle at one end.
  3. Trace the second side. Measure out a new line segment that is equal in length to the first. Start it at one end of the original line segment, where you measured the 60° angle. Start from the vertex (the point) of the angle, and trace the straight edge of the protractor until you reach the next "point."
  4. Finish the triangle. Use the straight edge of your protractor to trace out the final side of the triangle. Connect the point at the end of the second line segment to the unattached end of the first line segment. You should now have an equilateral triangle.

Tips

  • Use a compass that has a lock to ensure that you don't unintentionally change the spread of the compass.
  • Don't make the compass lines dark; you want them to be thin so you can easily erase them later.
  • The compass method is usually more precise as it does not rely on the correct measurement of angles.

Warnings

  • Don't mark the surface beneath the paper.

Things You'll Need

  • A pair of compasses (the type used for mathematical constructions, not the North/South type)
  • Something to put under the compass so the point doesn't slip
  • A ruler
  • A pencil (try not to use mechanical pencils, they may not fit into the pencil holder on the compass). Also make sure it is sharp, not blunt.
Теги:
Information
Users of Guests are not allowed to comment this publication.